| Inspection |
Notes |
Performed By |
Date |
| Passed: Engineering - Setbacks |
Tight Lot Setbacks Need Surveyor Verification |
Anthony Aslan |
11/3/2022 |
| Passed: Building - Footer |
Clean Out Footings Where Needed |
Anthony Aslan |
11/3/2022 |
| Passed: Building - Lintel/Tie Beam |
|
Anthony Aslan |
11/8/2022 |
| Passed: Electrical - Permanent Power |
Need Elevation Certificate , Need Spetic Release |
Anthony Aslan |
12/20/2022 |
| Failed: Electrical - Permanent Power |
Received Elevation Certificate And Electric Meter Is Below Required One Foot Above Base Flood Elevation. Need To Raise And Have Elevation Certificate Revised. |
Troy Crews |
12/27/2022 |
| Cancelled: Modular - Strapping |
|
Troy Crews |
1/9/2023 |
| Cancelled: Electrical - Temporary Service |
|
Troy Crews |
1/9/2023 |
| Failed: Modular - Strapping |
Need New Elevation Certificate To Include Power Meter Being Raised. Prior To Permanent Power-- Elevation Certificate Rec'd-- Electric Meter Still Below Mfe |
Troy Crews |
1/17/2023 |
| Cancelled: Modular - Strapping |
|
Emaleigh Williams |
1/20/2023 |
| Passed: Electrical - Permanent Power |
-need Septic Release
-e3705.7location Of Overcurrent Devices In Or On Premises.
overcurrent Devices Shall:
1.be Readily Accessible. [240.24(a)]
2.not Be Located Where They Will Be Exposed To Physical Damage. [240.24(c)]
3.not Be Located Where They Will Be In The Vicinity Of Easily Ignitable Material Such As In Clothes Closets. [240.24(d)]
4.not Be Located In Bathrooms. [240.24(e)]
5.not Be Located Over Steps Of A Stairway.
6.be Installed So That The Center Of The Grip Of The Operating Handle Of The Switch Or Circuit Breaker, When In Its Highest Position, Is Not More Than 6 Feet 7 Inches (2007 Mm) Above The Floor Or Working Platform. [240.24(a)]
-e3705.8ready Access For Occupants.
each Occupant Shall Have Ready Access To All Overcurrent Devices Protecting The Conductors Supplying That Occupancy
-e3405.4outdoor Dedicated Panelboard Space.
the Outdoor Space Equal To The Width And Depth Of The Panelboard, And Extending From Grade To A Height Of 6 Feet (1.8 M) Above The Panelboard, Shall Be Dedicated To The Electrical Installation. Piping And Other Equipment Foreign To The Electrical Installation Shall Not Be Located In This Zone. |
Anthony Aslan |
1/25/2023 |
| Release to power company |
|
Melissa Garber |
1/26/2023 |
| Septic Release Inspection |
|
Health Dept |
1/26/2023 |
| Failed: Building - Final |
-dryer Vent Must Be Smooth Pipe
-under Pinning Needs To Be Taped Up
-platform For Panel Is Incorrect, No Handrails And About 2'ft Away From Panel
-some Out Riggers On Frame Cut
-wedges On All Piers Are Not Installed Correctly, Not Touching Or Overlapping Each Other
-no Hand Rails On Stairs |
Anthony Aslan |
1/31/2023 |
| Passed: Building - Final |
*the Dryer Pipe Crimped Is Facing In The Direction Of Air Flow, Needs To Meet These Minimum Codes, Although It Is Smooth There Is No Gauge Stamped On The Aluminum Pipe. If You Can Provide Manufacture Specs On Pipe That Meet The Minimum Code Requirements.
sectionm1502
clothes Dryer Exhaust
m1502.4dryer Exhaust Ducts.
dryer Exhaust Ducts Shall Conform To The Requirements Of Sections M1502.4.1 Through M1502.4.7.
m1502.4.1material And Size.
exhaust Ducts Shall Have A Smooth Interior Finish And Be Constructed Of Metal Having A Minimum Thickness Of 0.0157 Inch (28 Gauge). The Duct Shall Be 4 Inches (102 Mm) Nominal In Diameter.
exception: Exhaust Ducts May Be 4 Inches Nominal In Diameter Schedule 40 Pvc When Horizontally Run Beneath The Slab.
m1502.4.2duct Installation.
exhaust Ducts Shall Be Supported At Intervals Not To Exceed 12 Feet (3658 Mm) And Shall Be Secured In Place. The Insert End Of The Duct Shall Extend Into The Adjoining Duct Or Fitting In The Direction Of Airflow. Exhaust Duct Joints Shall Be Sealed In Accordance With Section M1601.4.1. Ducts Shall Not Be Joined With Screws Or Similar Fasteners. Where Dryer Exhaust Ducts Are Enclosed In Wall Or Ceiling Cavities, Such Cavities Shall Allow The Installation Of The Duct Without Deformation. |
Anthony Aslan |
2/3/2023 |
| Certificate-Release Certificate |
Contractor Needs To Get State Final Inspection Results. |
Anthony Aslan |
2/9/2023 |
